Front Range air is dry for most of the year, which makes it easy to assume mold is somebody else's problem. Two common household machines, the evaporative (swamp) cooler and the furnace or portable humidifier, put water into the air on purpose, and that is where many Denver-area homes pick up mold they cannot explain.
Why a dry place still gets indoor mold
Metro Denver Economic Development, citing NOAA, lists the city's average annual precipitation at 15.6 inches and its average afternoon humidity at 43 percent. Outdoors, that is a dry climate. Mold does not need a wet climate, though. It needs a damp surface, a food source such as dust, paper, wood or drywall, and time. Inside a house, the dampness almost always comes from a specific source, and in a dry region the sources people forget about are the ones that were installed to add moisture.
That is the reason a Colorado homeowner can have a spotless, bone-dry living room and still find black or green growth around a cooler, on a bedroom windowsill in January, or inside a duct near a humidifier. The machine is doing exactly what it was built to do. The problem is what happens to the water it uses when nobody is looking after it.
How a swamp cooler puts moisture in your house
An evaporative cooler pulls outside air across wet pads and pushes the cooled, wetter air into the house. The U.S. Department of Energy says evaporative coolers add moisture to indoor air, are only suitable for areas with low humidity, and need regular upkeep such as checking the pads, filters, reservoir and pump, plus a full cleaning each season. That short list explains most swamp cooler mold. A pad that stays damp for weeks, a reservoir with standing water, or a drain that does not empty will grow a film long before it fails mechanically.
Roof-mounted and window units on older bungalows, ranches and split-levels are especially exposed. Water sits in the pan through a cool spring, the unit is switched on in June, and the first blast of air carries whatever has grown over the winter into the rooms below. Units that were shut down badly in the fall, with water left in the pan and the cover left open to rain and snowmelt, are the usual culprits.
Where to look on a cooler
- The pads. Dark spots, a slimy feel, or a sour smell when the unit starts mean the pads are past reusing.
- The reservoir and pump. Slime or film on the pan walls, and mineral crust mixed with dark growth around the float.
- The cabinet and roof curb. Rust, leaks, or staining where the unit meets the roof. A slow leak here can wet the ceiling below without ever being noticed.
- The duct drop and the ceiling vent. Staining on the ceiling around a supply vent, or a musty smell only when the cooler runs.
Humidifiers: the winter version of the same problem
Winter in Colorado is dry enough that many households run a humidifier, either a portable one in a bedroom or a unit mounted on the furnace. A furnace humidifier uses a pad or drum with water flowing over it, and a portable one holds a tank of water that can stay warm and still for days. Both can grow a film if they are not emptied, cleaned and dried on the schedule in the maker's manual.
The bigger issue is how much moisture ends up in the house. EPA advises keeping indoor humidity below 60 percent relative humidity, ideally between 30 and 50 percent. A humidifier set high on a cold night can push a small bedroom well past that range, and single-pane or older windows then give the moisture a cold surface to land on. Water beading on the glass, a damp sill, or peeling paint at the window frame are all signs the setting is too high for the house. A basic hygrometer from a hardware store takes the guessing out of it.
The forced-air furnace connection
Many Front Range houses have a furnace in the basement with ductwork running through the joist bays. Whatever the furnace humidifier or the cooler leaves in the air can reach the ducts. Moisture inside metal ductwork is not common, but it happens where a humidifier drips, where a drain line is clogged, or where a cooler drop is connected to the same runs. A musty smell that arrives with the first blast of heat in the fall, or the first blast of cool air in summer, points toward the equipment and the ducts rather than a wall. Our page on furnace, duct and swamp cooler mold explains what a local company looks at in those cases.
Do not run the system to find out. If you can see dark growth on a register, inside a supply boot, or on the pad of a humidifier, running the fan spreads it. Turn the equipment off and keep it off until you know what you are dealing with.
A simple seasonal routine
Most of this comes down to habits that take a few minutes a year. Follow the maker's manual first, and use the Department of Energy's list as a checklist.
- Spring start-up. Before the first use, open the cabinet, look at the pads, the reservoir, the pump and the float. Replace pads that are dark, stiff or smell sour. Clean mineral buildup and film from the pan.
- Mid-season. Check the pads and the water line every few weeks. A pad that stays wet while the unit is off needs attention.
- Fall shut-down. Drain the reservoir, clean it, let everything dry, and cover the unit so snowmelt cannot get in. Close the duct damper if there is one.
- Humidifier habits. Empty and dry portable tanks daily when they are in use. Replace furnace humidifier pads on the schedule in the manual. Set the humidity with a hygrometer rather than by feel.
- Watch the windows. If glass is wet in the morning, the humidity setting is too high for that house.
Signs the problem has gone beyond maintenance
Cleaning a pad or a pan is a maintenance job. Mold on building materials is a different matter. Look for these:
- Dark growth on a ceiling or wall near a cooler, vent or humidifier
- Soft, bubbling or stained drywall or ceiling texture
- A musty smell that stays after the equipment is off for a day or two
- Growth visible inside a register, boot or duct
- Water stains on the ceiling below a roof-mounted cooler
EPA's guide describes patches of less than about 10 square feet, roughly a 3 ft. by 3 ft. area, as ones many people can handle themselves, and points to its remediation guidance for larger areas or significant water damage. That rule fits a spot on a window frame or a bit of film on a pad. It does not fit ductwork, a wet ceiling or a leaking roof curb. The article on DIY cleanup versus a professional walks through the line in more detail.
Stop the water first. If a cooler leak is the cause, shut the unit and its water supply off. Cleaning a ceiling without fixing the leak above it only buys a few weeks. If the problem keeps coming back after you clean, a mold inspection can help trace the moisture path rather than guess at it.
What a local company usually does
The work depends on what is affected. For a cooler or humidifier alone, you may only need a repair person or a replacement pad. When growth is on drywall, ceiling texture or ductwork, a local mold company will typically find and describe the moisture source, set up containment, remove or clean the affected materials, and dry the area. Ductwork is usually a specialist job, since the system has to be cleaned without blowing particles through the rest of the house. The guide on what happens during remediation lays out the steps in order.
On cost, a Denver cost guide (Angi) puts HVAC and duct mold cleaning at roughly $3,000 to $10,000 per project, and drywall repair after mold removal at roughly $1,000 to $2,900. Those are published ranges for the area, not quotes. A small pad-and-pan problem costs a fraction of that, which is the best reason to look after the machine every season.
Hiring and paperwork
Colorado does not require a state mold remediation license, so there is no state mold license to look up. Contractor licensing is handled locally. The City and County of Denver issues its own contractor licenses and certificates and states that it does not accept or reciprocate those from other counties or states, so ask any company that works on your system or ceiling which local license it holds. Replacing a cooler or running new ductwork can also involve a building permit, which in Denver comes from Community Planning and Development. Our overview of Colorado mold rules and hiring covers what to ask.
Renters should know that the person who maintains the cooler or the furnace humidifier is usually the landlord. If you rent and the equipment is causing damp or mold, put the problem in writing. Colorado's warranty of habitability can treat a home as uninhabitable where there is mold associated with dampness, after notice. Read mold in a Colorado rental before you decide what to send.
If it already smells
If the odor is the only clue, see the musty smell guide, which covers hidden sources beyond coolers and humidifiers. If you have found a wet or stained ceiling, the leak and burst pipe mold page is the closer match. For a quick view of everything we connect callers with, see the full list of services.
If you have health concerns about living with the problem, talk with your doctor. The CDC states that exposure to damp, moldy environments may cause a variety of health effects, or none at all, and that people with asthma or mold allergies may have severe reactions.
Frequently asked questions
Can a swamp cooler cause mold in my house?
What humidity should I keep with a humidifier running?
Should I run my cooler or furnace if I see mold on it?
Who pays for mold from a swamp cooler in a rental?
Sources
- U.S. Department of Energy: evaporative coolers
- EPA: A Brief Guide to Mold, Moisture and Your Home
- Metro Denver Economic Development: climate
- CDC: About mold and health
- How Much Does Mold Remediation Cost in Denver, CO? | Angi
- Denver Community Planning and Development: Contractor Licensing
- Colorado Legal Services: warranty of habitability
Last updated: