Mold remediation referrals for Denver & nearby townsCall: (720) 818-9506
(720) 818-9506

What happens during mold remediation, step by step

moldremediationdenverco.net

Mold remediation is a sequence of jobs, and the order matters. This guide walks through the stages in a typical Denver-area home so you can read a company's written scope, ask sensible questions and know what normal looks like.

Need mold help now?
Call now to be connected with a local mold remediation company in Denver.
(720) 818-9506

Mold remediation is a sequence of jobs, and the order matters. This guide walks through the stages in a typical Denver-area home so you can read a company's written scope, ask sensible questions and know what normal looks like.

The short version

Remediation means finding the moisture that fed the mold, containing the affected space, removing or cleaning contaminated materials, drying the structure, cleaning the surrounding area, and confirming the result. Rebuilding is usually a separate phase. Each company words its scope differently and every house is different, so treat the stages below as a general pattern, not a promise of what any one company will do.

EPA's household guide notes that areas of less than about 10 square feet are ones many people can handle themselves, and points to EPA remediation guidance for larger areas or significant water damage. This guide is about the larger jobs. If you are still deciding whether yours is one of them, start with our comparison of DIY cleanup and hiring a pro.

Step 1: The assessment and the moisture source

A visit usually begins with a walk-through. The company looks at the visible growth, asks about the history of the space, and uses a moisture meter, and sometimes a thermal camera, to find damp materials that do not look wet. This is where the real cause is traced. In Colorado, outdoor air is dry for most of the year, so indoor mold almost always traces to a specific water event or a chronic condition: a slow plumbing leak, a failed washer hose, a roof leak after snow, a window well that drains poorly, foundation seepage, or a humidifier or evaporative cooler running without upkeep. Metro Denver Economic Development, citing NOAA, lists Denver's average annual precipitation at 15.6 inches and average afternoon humidity at 43 percent, which is why a damp interior stands out.

The assessment may be called an inspection. It is different from lab sampling, and the two are often confused. Our explanation of mold inspection covers what an inspector looks at, and inspection versus testing covers when samples add anything. EPA states that in most cases, if visible mold growth is present, sampling is unnecessary, and that no EPA or other federal limits have been set for mold or mold spores.

The output of this step should be a written scope: where the mold is, which materials are affected, what will be removed, what will be cleaned, and what the company will not cover, such as the plumbing repair itself.

Step 2: Fix the water

No amount of cleaning outlasts a leak. Before or alongside remediation, the water source has to be stopped. A remediation company may not repair plumbing, roofing or grading, so expect a plumber, roofer or drainage contractor to handle that part. If a pipe burst or a fixture failed, the speed of drying matters, and our guide to mold after a burst pipe or leak lays out the early hours. For recurring water problems, the burst pipe and leak mold page explains how the two jobs fit together.

Step 3: Containment and air control

Disturbing mold releases spores and fragments into the air. Containment keeps them from reaching the rest of the house. Typical measures include:

  • Plastic sheeting taped over doorways, openings and sometimes the whole work zone.
  • A zipper door so workers can pass without opening the barrier.
  • Negative air pressure, created by a fan that exhausts air from the work zone through a HEPA filter, so air leaks in rather than out.
  • Covering or sealing supply and return vents, and shutting down the furnace or air handler in the affected area while work is underway.

Ask how the company contains the area and where the air is exhausted. A basement job in a Denver bungalow with a forced-air furnace in the same space needs particular attention, because the ductwork can move air through every floor.

Step 4: Protective gear and removal

Workers should wear respirators, disposable coveralls, gloves and eye protection. Removal follows a rough order, from the most contaminated materials to the least:

  1. Porous materials that have mold growing through them are removed and bagged. That includes wet drywall, carpet and pad, ceiling tiles and insulation.
  2. Bags are sealed before leaving the containment so debris is not dragged through the home.
  3. Semi-porous materials such as framing lumber are cleaned, often by sanding, HEPA vacuuming or wire-brushing, then wiped down.
  4. Non-porous materials such as metal, glass and sealed concrete are cleaned with detergent and water.

How much comes out depends on the material and how long it stayed wet. Wall cavities are a common surprise: growth that looks like a patch on a painted surface can run up the back of the drywall. Our page on mold in walls explains how companies decide where to cut and how they handle the opening.

Step 5: Drying the structure

After removal, the remaining materials must be brought down to a normal moisture level. Companies use air movers and commercial dehumidifiers, sometimes with heaters in a cold space, and take moisture readings until the structure is dry. This stage is quieter than demolition, but it is what stops regrowth. EPA advises keeping indoor humidity below 60 percent, ideally between 30 and 50 percent, which is also the range you should aim for afterward.

Step 6: HEPA cleaning

With the contaminated materials gone, the work zone is vacuumed with HEPA-filtered equipment and wiped down, including surfaces that were not visibly affected. This removes settled dust and fragments. Cleaning typically goes from the top of the room to the bottom, ending with the floor. Some companies also treat the area with a sealant or coating. If a coating is part of the scope, ask what it is for and what it does not do. A coating is not a substitute for dry framing.

Step 7: Confirming the result

Most companies finish with a visual inspection and a moisture check. Some jobs also call for a separate party to perform clearance sampling afterward. This is not required by a Colorado mold law, but it can be useful if the job was large, if a lender, buyer or landlord asks for documentation, or if you want an outside check. Details on what it does and does not show are in our guide to post-remediation clearance testing, and the service page for clearance testing in Denver covers how to arrange it. Ask for it in the scope in advance, and ask that the tester be someone other than the crew doing the cleanup.

Step 8: Rebuilding

Many mold companies do not rebuild. Replacing drywall, trim, flooring and paint may be a separate contractor or a separate line in the same agreement. A Denver cost guide from Angi lists drywall repair after mold removal at about $1,000 to $2,900 per project. Whether work like that needs a building permit depends on its scope, so ask the building permit office that serves your address. In Denver that is Community Planning and Development.

What it costs

Published figures give a sense of range. A Denver cost guide from Angi lists mold remediation overall at about $1,109 to $3,112 per project. HomeBlue's Denver figures show roughly $5,200 to $10,300 for a 500-square-foot area, or about $10 to $21 per square foot. Angi's Denver guide puts the per-square-foot range at about $10 to $25. These are published ranges for guidance, not quotes. See our Denver mold remediation cost guide for how scope, access and materials move a price, or visit the mold removal and remediation page for the service overview.

Hiring and paperwork

Colorado does not require a state mold remediation license, so there is no state mold license to look up. Contractor licensing is local. The City and County of Denver issues its own contractor licenses and certificates and does not accept or reciprocate licenses or certificates from other counties or states. Ask the company which local contractor license it holds for the work, and get a written scope covering containment, removal, drying, cleaning, who handles rebuilding and what happens if the mold returns. Our checklist for hiring in Colorado goes through it.

Tenants should know that Colorado's warranty of habitability can apply to mold associated with dampness, and that the landlord generally needs written notice before repairs are required. That is a legal question between you and your landlord, and the remediation company is not a party to it.

If you want to be connected with an independent local company,

Call now to be connected with a local mold remediation company in Denver.
(720) 818-9506

Questions to ask before work starts

  • How will you contain the area, and where does the exhaust go?
  • Which materials will be removed, and which will be cleaned?
  • How will you confirm the area is dry before closing it up?
  • Who handles the water repair and the rebuild?
  • Is clearance sampling included, and who performs it?

If you have health concerns about being in the home during the work, talk with your doctor. The CDC states that the health effects of mold are different for different people.

Frequently asked questions

How long does mold remediation take?
It depends on the size, the materials and how long drying takes. Small contained jobs can be shorter, while wall cavities, basements and water-damaged structures take longer. Ask the company for a written schedule instead of relying on a general figure.
Do I have to leave my home during remediation?
Not always. It depends on the size of the work zone, how well it can be contained and whether the furnace and ducts are involved. If you have health concerns, talk with your doctor and ask the company about containment.
Is testing part of remediation?
Not necessarily. EPA says sampling is unnecessary in most cases where visible mold is present. Clearance sampling after the work is an optional step, often done by a separate party.
Does remediation include fixing the leak?
Usually not. Remediation deals with the mold and wet materials. A plumber, roofer or drainage contractor typically fixes the source, and it needs to be fixed for the cleanup to last.
Does the company rebuild afterward?
Some do, many do not. Ask whether drywall, flooring and paint are in the scope or handled separately, and whether a building permit is needed.
Call now to be connected with a local mold remediation company in Denver.
(720) 818-9506

Last updated:

☎ Call (720) 818-9506